OPENVPN MTU

VPN: Configuring the MTU setting

January 13, 2019 -  5 minute read

Finding an apartment in Berlin is hard and I had to switch between many before finding a permanent contract. A few times during this process I found that my VPN stopped working after moving to a new apartment. It took a little bit of investigation but I found the culprit to be the MTU setting. It turns out that misconfiguration of the MTU can cause problems and even stop requests working so getting it right is important.

Symptoms

I was seeing a few different things happening:

• Nothing loading over the internet at all
• Just the page title loading
• Really slow connection

What is an MTU?

MTU stands for Maximum Transmission Unit and can be thought of as the largest packet size that can be sent from your computer over the network to it’s destination. During the packet’s journey if it encounters a hop that can’t process it’s size then it will be fragmented or dropped - in which case an ICMP message “Destination Unreachable (Datagram Too Big)” will be returned.

The MTU can be discovered via the ‘Path MTU Discovery’ technique. This involves sending out a packet with the DF (Don’t Fragment) IP header set. This means that any hop that can’t support the packet size will have to return the ICMP message. The process is repeated until the smallest successful packet size is found. (See below for how we will do this manually).

Standard MTU sizes

Different network protocols and layers can handle different MTUs so your mileage may vary depending on your ISP and whether you are using IP4/IP6. Here is a table from wikipedia on the subject:

Media for IP transportMaximum transmission unit (bytes)Notes

Internet IPv4 path MTU	At least 68, max of 64 KiB	Practical path MTUs are generally higher. Systems may use Path MTU Discovery to find the actual path MTU. Routing from larger MTU to smaller MTU causes IP fragmentation.
Internet IPv6 path MTU	At least 1280, max of 64 KiB, but up to 4 GiB with optional jumbogram	Practical path MTUs are generally higher. Systems must use Path MTU Discovery to find the actual path MTU.
Ethernet v2	1500	Nearly all IP over Ethernet implementations use the Ethernet V2 frame format.
Ethernet with LLC and SNAP	1492
Ethernet jumbo frames	1501 – 9198 or more	The limit varies by vendor. For correct interoperation, the whole Ethernet network (segment) must support the same maximum frame size. Jumbo frames are usually only seen in special-purpose networks.
PPPoE v2	1492	Ethernet v2 MTU (1500) less PPPoE header
DS-Lite over PPPoE	1452	Ethernet v2 MTU (1500) less PPPoE header (8) and IPv6 header
PPPoE jumbo frames	1493 – 9190 or more	Ethernet Jumbo Frame MTU (1501 - 9198) less PPPoE header
WLAN (802.11)	2304	The maximum MSDU size is 2304 before encryption. WEP will add 8 bytes, WPA-TKIP 20 bytes, and WPA2-CCMP 16 bytes.
Token Ring (802.5)	4464
FDDI	4352

Working out the MTU

As described above we will perform a ‘Path MTU Discovery’ manually (for more details on the technique check out RFC1191 - IPv4, RFC1981 - IPv6). To do this we will use ping to send some packets out with the DF (Don’t Fragment) option set and a fixed packet size. We will start from the Ethernet v2 standard (1500) from the table above as this should cover all ISPs, and reduce the packet size by 10 until we get a successful response.

Here is the command we will use (I’m using MacOS here - check your distro for how to set the DF option):

$ ping -D -v -s 1500 -c 1 google.com

Here is how our discovery went:

⇨ ping -D -v -s 1500 -c 1 google.com PING google.com (216.58.210.46): 1500 data bytes ping: sendto: Message too long --- google.com ping statistics --- 1 packets transmitted, 0 packets received, 100.0% packet loss / ⇨ ping -D -v -s 1490 -c 1 google.com PING google.com (216.58.210.46): 1490 data bytes ping: sendto: Message too long --- google.com ping statistics --- 1 packets transmitted, 0 packets received, 100.0% packet loss / ⇨ ping -D -v -s 1480 -c 1 google.com PING google.com (216.58.210.46): 1480 data bytes ping: sendto: Message too long --- google.com ping statistics --- 1 packets transmitted, 0 packets received, 100.0% packet loss / ⇨ ping -D -v -s 1470 -c 1 google.com PING google.com (216.58.210.46): 1470 data bytes 72 bytes from 216.58.210.46: icmp_seq=0 ttl=53 time=275.188 ms wrong total length 92 instead of 1498 --- google.com ping statistics --- 1 packets transmitted, 1 packets received, 0.0% packet loss round-trip min/avg/max/stddev = 275.188/275.188/275.188/0.000 ms

So my MTU was 1470 after the last request was successful. You may have noticed the ‘wrong total length’ message ping gave me. This is due to Google sending back a small response. The request was successful though.

OpenVPN Configuration

The OpenVPN documentation states:

“MTU problems often manifest themselves as connections which hang during periods of active usage.

It’s best to use the –fragment and/or –mssfix options to deal with MTU sizing issues.”

… and …

“Both –fragment and –mssfix are designed to work around cases where Path MTU discovery is broken on the network path between OpenVPN peers.

The usual symptom of such a breakdown is an OpenVPN connection which successfully starts, but then stalls during active usage.”

We are using UDP protocol on our tunnel so we are going to use the mssfix option in our OpenVPN config file to reduce the packet size to fit within our MTU.

The manual states:

–mssfix max Announce to TCP sessions running over the tunnel that they should limit their send packet sizes such that after OpenVPN has encapsulated them, the resulting UDP packet size that OpenVPN sends to its peer will not exceed maxbytes. The default value is 1450.The max parameter is interpreted in the same way as the –link-mtu parameter, i.e. the UDP packet size after encapsulation overhead has been added in, but not including the UDP header itself. Resulting packet would be at most 28 bytes larger for IPv4 and 48 bytes for IPv6 (20/40 bytes for IP header and 8 bytes for UDP header). Default value of 1450 allows IPv4 packets to be transmitted over a link with MTU 1473 or higher without IP level fragmentation.

This suggests we need to take in to account the UDP header bytes. So 1470 - 28 (for IPv4) = 1442.

Incidentally I did check if the default setting for mssfix of 1450 which works with MTU of 1473 pass our ‘Path MTU Discovery’. It didn’t.

So I’ve added --mssfix 1442 to my OpenVPN config and it’s working fine for the moment :)

This article uses material from the Wikipedia article “Maximum transmission unit”, which is released under the Creative Commons Attribution-Share-Alike License 3.0.